Cleaning Oily Gunky Mildew Guns?

[Cavalry]

Long story short, I am involved in an estate with a substantial amount of firearms that have been neglected for a couple years. I am not a stakeholder but phrased it as I would be interested in helping out for first picks at a discounted rate. They were oiled but left to sit out in the open in a house with no attention. Dust, dander, etc has fallen on any horizontal surface and mildew has formed and is eating the dust as well some mildew on the oiled wood, fabric and leather. The mildew/dust on metal comes off but is very sticky.
If they were mine I would do a detail strip and just do it right. But I do not have that sort of time or inclination.

Thought #1 Pull the wood, wipe with water/vinegar. Metal goes in the solvent tank and gets scrubbed with a soft brush, blow off and oil

Thought#2 Go to town with my steamer on them assembled (outside). It will flash dry almost immediately so I am not worried about rust. As long as I dont dwell on the wood or damaged finish I do not foresee issues with the steam. Oil and send it.

 

[Saltwater60]

Try a diluted citrus based cleaner to see if it takes the sticky gunk off. It should. You can use fine steel wool and then oil it.
I like option one, but not the steamer idea.

 

[togmaster]

Do it right or do nothing.

 

[Cavalry]

Do it right or do nothing.

If they were mine I would completely agree. I would say at least an hour each to detail strip and clean which is not worth the time investment. This is more like make them not look disgusting.

 

[Robin]

I'd try windex spritz, let it sit for fifteen minutes and soak a rough terrycloth rag with windex and start a wipe down, rinsing often. If that works, wipe down the steel parts with oily rag, wood parts with lemon pledge aerosol, leather parts with neatsfoot oil. Easy!
Robin

 

[fresch]

Are they collectable? Take the time.
Are they run of the mill shooters? Clean em off and keep those doggies movin.

 

[FP1201]

Long story short, I am involved in an estate with a substantial amount of firearms that have been neglected for a couple years. I am not a stakeholder but phrased it as I would be interested in helping out for first picks at a discounted rate. They were oiled but left to sit out in the open in a house with no attention. Dust, dander, etc has fallen on any horizontal surface and mildew has formed and is eating the dust as well some mildew on the oiled wood, fabric and leather. The mildew/dust on metal comes off but is very sticky.
If they were mine I would do a detail strip and just do it right. But I do not have that sort of time or inclination.

Thought #1 Pull the wood, wipe with water/vinegar. Metal goes in the solvent tank and gets scrubbed with a soft brush, blow off and oil

Thought#2 Go to town with my steamer on them assembled (outside). It will flash dry almost immediately so I am not worried about rust. As long as I dont dwell on the wood or damaged finish I do not foresee issues with the steam. Oil and send it.

Smokers in the House? They get covered with a film of nicotine and dust that's nasty and difficult to get off without a serious solvent such as Acetone or Lacquer Thinner (which I recommend with proper PPE) The Furniture will dry out and look devoid of finish, but that's really just the surface and really should be thoroughly cleaned including a light sanding with Copper or Stainless Wool.
I suppose one could cheat to get a quick & dirty by spraying the action or surfaces needed for inspection with a can of Carburetor Cleaner and paper towels.
On the inverse, I had to recover and preserve about fifty guns from a House Fire: smoke & water only, so I bought gallon cans of WD-40 with Spray Bottle: sopped and slathered it on and inside...worried about "cleaning" them all later...worked.

Another simple chemical that works remarkably well is "Foamy Glass Cleaner with Ammonia" it's astounding how much gunk will come up with that stuff, and it works great sprayed into Bores/actions after shooting corrosive ammunition.

 

[Saltwater60]

Smokers in the House? They get covered with a film of nicotine and dust that's nasty and difficult to get off without a serious solvent such as Acetone or Lacquer Thinner (which I recommend with proper PPE) The Furniture will dry out and look devoid of finish, but that's really just the surface and really should be thoroughly cleaned including a light sanding with Copper or Stainless Wool.
I suppose one could cheat to get a quick & dirty by spraying the action or surfaces needed for inspection with a can of Carburetor Cleaner and paper towels.
On the inverse, I had to recover and preserve about fifty guns from a House Fire: smoke & water only, so I bought gallon cans of WD-40 with Spray Bottle: sopped and slathered it on and inside...worried about "cleaning" them all later...worked.

Another simple chemical that works remarkably well is "Foamy Glass Cleaner with Ammonia" it's astounding how much gunk will come up with that stuff, and it works great sprayed into Bores/actions after shooting corrosive ammunition.

A fire is my worst nightmare

 

[Cavalry]

Smokers in the House? They get covered with a film of nicotine and dust that's nasty and difficult to get off without a serious solvent such as Acetone or Lacquer Thinner (which I recommend with proper PPE) The Furniture will dry out and look devoid of finish, but that's really just the surface and really should be thoroughly cleaned including a light sanding with Copper or Stainless Wool.
I suppose one could cheat to get a quick & dirty by spraying the action or surfaces needed for inspection with a can of Carburetor Cleaner and paper towels.
On the inverse, I had to recover and preserve about fifty guns from a House Fire: smoke & water only, so I bought gallon cans of WD-40 with Spray Bottle: sopped and slathered it on and inside...worried about "cleaning" them all later...worked.

Another simple chemical that works remarkably well is "Foamy Glass Cleaner with Ammonia" it's astounding how much gunk will come up with that stuff, and it works great sprayed into Bores/actions after shooting corrosive ammunition.

Non smoking home. They leave their windows open in the summer so its not humidity controlled, entrance of pollen, dirt, etc. Dude was sick for a couple years. He wasn't able to keep up on the maintenance for that environment but did previously.

Sprayway glass cleaner is a good idea. I have not tried it. That might work soften the gunk and blow it off with compressed air.

 

[Cavalry]

Are they collectable? Take the time.
Are they run of the mill shooters? Clean em off and keep those doggies movin.

Not collectable in a sense of high dollar but not beat up Montgomery Ward field guns. Mixed but there is a fair amount of milsurp

 

[Saltwater60]

Non smoking home. They leave their windows open in the summer so its not humidity controlled, entrance of pollen, dirt, etc. Dude was sick for a couple years. He wasn't able to keep up on the maintenance for that environment but did previously.

Sprayway glass cleaner is a good idea. I have not tried it. That might work soften the gunk and blow it off with compressed air.

Just cooking or living in your home will cause that sticky crap to form. We have it in our home and we don’t leave the windows open much.

 

[Mosinitis]

Breakfree CLP should remove all the sticky stuff, surface rust and it shouldn't effect stock finish. There is a special wax that will clean and rejuvenate leather, turner saddlery or similar.

If there is no rust deeper than surface rust, should be an easy fix for everything.

I have guns I haven't touched in many years, treated with CLP and put away in the safe, no issues of any kind. The same goes for tools.

 

[togmaster]

If you just want to give them a quick dust off just wipe everything off with Ballistol. Good for metal, wood and leather.

 

[FP1201]

Non smoking home. They leave their windows open in the summer so its not humidity controlled, entrance of pollen, dirt, etc. Dude was sick for a couple years. He wasn't able to keep up on the maintenance for that environment but did previously.

Sprayway glass cleaner is a good idea. I have not tried it. That might work soften the gunk and blow it off with compressed air.

I have found that spraying the stock with FGC given a couple minutes lifts the old oil/funk, proof is in the paper towels, couple applications and wipes.

 

[Cavalry]

Breakfree CLP should remove all the sticky stuff, surface rust and it shouldn't effect stock finish. There is a special wax that will clean and rejuvenate leather, turner saddlery or similar.

If there is no rust deeper than surface rust, should be an easy fix for everything.

I have guns I haven't touched in many years, treated with CLP and put away in the safe, no issues of any kind. The same goes for tools.

There is no rust to speak of as they were oiled I believe with CLP as I saw some there. The problem I ran into with the test subject is the nooks and crannies for example around a hooded sight. CLP loosened but did not remove the dust/mildew. Blowing off with compressed air makes a mess.

 

[Mosinitis]

There is no rust to speak of as they were oiled I believe with CLP as I saw some there. The problem I ran into with the test subject is the nooks and crannies for example around a hooded sight. CLP loosened but did not remove the dust/mildew. Blowing off with compressed air makes a mess.

Never saw mildew on oiled metal, are you sure it's not gummed up oil?
Double ended tooth brush from M16 cleaning kit and pipe cleaners with stiff bristles should take care of gunk once it is loosened by CLP. You don't need to get it out from every nook and cranny, only where it interferes with function. It's oil based rust protection.
Just like cosmoline on surplus guns, I don't take all of it out, just most of it and from places where it is in the way, like bore and chamber of the barrel and bolt parts.

 

[Saltwater60]

Never saw mildew on oiled metal, are you sure it's not gummed up oil?
Double ended tooth brush from M16 cleaning kit and pipe cleaners with stiff bristles should take care of gunk once it is loosened by CLP. You don't need to get it out from every nook and cranny, only where it interferes with function. It's oil based rust protection.
Just like cosmoline on surplus guns, I don't take all of it out, just most of it and from places where it is in the way, like bore and chamber of the barrel and bolt parts.

Mildew might be from all the dust and stuff stuck to it.

 

[Cavalry]

Never saw mildew on oiled metal, are you sure it's not gummed up oil?
Double ended tooth brush from M16 cleaning kit and pipe cleaners with stiff bristles should take care of gunk once it is loosened by CLP. You don't need to get it out from every nook and cranny, only where it interferes with function. It's oil based rust protection.
Just like cosmoline on surplus guns, I don't take all of it out, just most of it and from places where it is in the way, like bore and chamber of the barrel and bolt

No, metal alone will not mildew. Heavy dust has deposited on the oiled metal, mildew is eating the dust.

 

[Robin]

Be careful!

Matango, Fungus of Terror (1963)

Don’t eat the mushrooms… Japanese poster Also known as ATTACK OF THE MUSHROOM PEOPLE or simply MATANGO, Ishiro (GOJIRA) Honda’s horror film is partly based on the short story &#82…

monsterzone.org

Robin