Target
6.5 Creedmoor
I've been reading a lot of PAW stories lately. I see your property and fantasize of the homesteads the main characters on the stories build.
Very nice!
Starting a "What did you Get today" thread. Let's give it a try (dont forget pics)
- Thread starter Edwardteach72
- Start date
I've been reading a lot of PAW stories lately. I see your property and fantasize of the homesteads the main characters on the stories build.
Very nice!
spat
.950 JDJ
I can fit a 300yd rifle range in around the hills across the back.
There are a also a bunch of great places to setup some cool pistol ranges where you have effectively a mountain for the berm on about 300 degrees around you.
Might end up just setting one up off the back patio though
I will have targets and a bench set up shortly after we move in. I am sure the range itself will be subject to continuous improvement for quite some time though
After making me read all that...I saw nothing regarding a forum range day. Lmaooo But in all seriousness...I’m sure it’ll be a sweet setup man.I can fit a 300yd rifle range in around the hills across the back.
There are a also a bunch of great places to setup some cool pistol ranges where you have effectively a mountain for the berm on about 300 degrees around you.
Might end up just setting one up off the back patio though
I will have targets and a bench set up shortly after we move in. I am sure the range itself will be subject to continuous improvement for quite some time though
BDinPutnam
.475 A&M Magnum
If you bring the hardware, I'm going, come hell or high water!
spat
.950 JDJ
Any of you who find yourselves in Southern AZ are welcome anytime.
NEEDLE SCALER
My Lodge Cast Iron Griddle is getting a bit rusty (first pic is a new one).
Then there is mine:
It likely does not require ANYTHING, but I think I want to clean it down to bare metal.
Anyhow, I was a HF, and had this in my cart, for $7.99
Then I thought, why am I wasting my money on a tool that will be inadequate ?
When I could buy this, and own a real tool.
So I bought it.
And this buxomly gal sure seems to like her Needle Scaler a lot !
My Lodge Cast Iron Griddle is getting a bit rusty (first pic is a new one).
Then there is mine:
It likely does not require ANYTHING, but I think I want to clean it down to bare metal.
Anyhow, I was a HF, and had this in my cart, for $7.99
Then I thought, why am I wasting my money on a tool that will be inadequate ?
When I could buy this, and own a real tool.
So I bought it.
And this buxomly gal sure seems to like her Needle Scaler a lot !
Last edited:
Target
6.5 Creedmoor
You say that now from the safety of a state 2000 miles away.
I'm sure is we show up to your door, it'll be " No hablo ingles"
spat
.950 JDJ
Well, I've only got one guest room, so if you all show up at once and want to spend the night you'd better bring some tents or be prepared to get cozy.You say that now from the safety of a state 2000 miles away.
I'm sure is we show up to your door, it'll be " No hablo ingles"
And ammo, bring lots of ammo.
But I'm always happy to put some down range, so come on
Two men enter, one man leaves...welcome to the Thunderdome bitches!Well, I've only got one guest room, so if you all show up at once and want to spend the night you'd better bring some tents or be prepared to get cozy.
And ammo, bring lots of ammo.
But I'm always happy to put some down range, so come on
knuts
.45 acp
BDinPutnam
.475 A&M Magnum
Well maybe 15-20 years from now I'll take a ride down the highway from up Flagstaff way...
kev74
20×102mm Vulcan
If you toss that bad boy in the oven and run the clean cycle, it will come out like new. All the carbon will burn off.
It's more than that, though.
There is heavy rust from being stored four seasons, outside, in the grill.
spat
.950 JDJ
The needle scaler is for heavy scale, not just rust.
If you can’t flake dime sized chunks off with a knife it's not for this.
If you can, the cookware is probably past saving.
Get the carbon out of the way in an oven like suggested.
Then get rid of most of the rust mechanicaly with some sandpaper or a sand blaster.
Finish off the last bits chemically with some acid based rust remover.
Should be able to get them nice and shiny clean that way.
Depending on how bad the rust was you might need more sandpaper to get the surface finish back to an acceptable texture.
Then re-season and go.
Got my saw last night. I put it together but still have some fine tuning to do.
You found a little girl to bring home? Awesome, just in time for snow season for shoveling!
PX24CMO Combo Kit - Stealth Cam
PX24CMOK features a 24 MP FX Shield, Video recording 15 seconds, 18 IR Emitters, Rubbed Face Plate, Combo Bat & 16 SD. The kit includes 8 AA Duracell Batteries, 16GB SD Memory Card, and a Nylon mounting strap.
www.stealthcam.com
Just ordered five of these.
I usually don't like to put my kids on social media, but that was the only picture I had of the saw. By the time I got done putting it together it was very dark on the second floor. I really should but the light circuits in next.
LOL Shes the evil one! She likes to pinch you and smile and ask if it hurts! She loves motorcycles too..... Yup shes probably going to cause me to go to jail when she gets older!
Don't ask how much I paid, I am ashamed. Also-
What's up with this potato chip bag shit? They could easily fit 1,000 rounds in there.
On a low mount a red dot would be a great choice for a deer huntin' lever gun in the woods.
Oh completely agree. Just thought the unity fast mount set up was funny
kev74
20×102mm Vulcan
I picked up some powder today.
kev74
20×102mm Vulcan
I got a few more bank deposit bags. They're handy for keeping pistol magazines organized.
