@GOPerfect check out www.chandlerhardwoods.com
I want yet another AR-15
- Thread starter GOPerfect
- Start date
FrankenCub
.338 Win Mag
BBQ paint. The cama paint on mine is still looking good, stayed put so far.
Well that's cheap enough.
BDinPutnam
.475 A&M Magnum
I have bought several of their receivers and handguards, they sell good stuff. did you see the 3 piece AR10 set? might be good to put one away for a rainy day.
Robin
.577 Tyrannosaur.
Robin
spat
.950 JDJ
They aren't that difficult. Jig does most of the work.
BDinPutnam
.475 A&M Magnum
Man this thread has me itching to do a build. Might be time to order the last 2 parts I need for another .223 Wylde- all I need is a mid/rifle handguard and stripped upper.
And @dsdmmat your endorsement carries a lot of weight, I may finally have to finally break down and do a '10 - if I can find someone to transfer the lower for me. Probably wait until May for that.
Sorry for momentary hijack!
And @dsdmmat your endorsement carries a lot of weight, I may finally have to finally break down and do a '10 - if I can find someone to transfer the lower for me. Probably wait until May for that.
Sorry for momentary hijack!
The matrix takes a Armalite lower parts kit. The takedown pins, bolt stop and rear detent spring are different than the DPMS. There is a place in Florida I got my parts from. I will find a link.
BDinPutnam
.475 A&M Magnum
The guy and place I got mine from is Chris at Central Florida Firearms. I will have to find link.I'll try to resurrect an appropriate thread.
Here is the manufacturer website.
Last edited:
Here is the link to my matrix build on the AR308 forum.
forum.308ar.com
Matrix build
so I was going to build a straight pull bolt AR308 but my barrel would not have a thick enough shank after all the work would have been done. Now I have a matrix set upper and lower with handguard on the way. Should be here Friday. I have some concerns about the forward assist as I have read peop...
forum.308ar.com
That's a little more challenging than a straight-up assembly, but it really isn't that difficult. You pay for it though... your stripped Anderson lower sells for +/- $ 45. To cut your own will cost you +/- $ 200 or more. Jig, end mills, 80% lower, and you need a good drill press or milling machine, calipers, and time. Also, expect to F' k up your first one. Now, that being said, if you plan on building a bunch of your own lowers, it might be worth it.
Should you actually consider buying a jig and tooling, remember that not all jigs are created equal. I have used several different ones, and have developed a preference for one. I can tell you where to get end mills locally, too. PM me if you want info.
Oh, and keep in mind that if you make your own, MONKEY FACE WILL HATE YOU, CALL YOU EVIL, AND TURN YOU INTO A FELON WITH THE STROKE OF A PEN.
Robin
.577 Tyrannosaur.
I personally know a guy that is willing to loan you his jig.
Robin
Shadow rider
6.5 Creedmoor
Shadow rider
6.5 Creedmoor
I used this for my latest build ( with an 80% lower)...
I'm really diggin the side charging concept!
side charging complete upper
finished product (the one on the right)...
I'm really diggin the side charging concept!
side charging complete upper
finished product (the one on the right)...
alistair
6.5 Creedmoor
From another site;
nyfirearms.com
5d Tactical 80% milling kit
Used 5d tactical milling kit for AR 80% lowers. Includes 5d kit (used for 1 aluminum lower). Mikita router (higher end routers work better than cheapos) Un-milled poly 80% lower. $220. Prefer a local sale but can ship for the right buyer. Located in WNY.
nyfirearms.com
alistair
6.5 Creedmoor
alistair
6.5 Creedmoor
Look forward to hearing more about this upper. I am just about to buy one.
Shadow rider
6.5 Creedmoor
80% is doable with a multi speed drill press (I use my Shopsmith) and a couple end mill bits and a cheap jig (mine was around $50 a few years back).
BDinPutnam
.475 A&M Magnum
ArmedCorgi
.475 A&M Magnum
Hurry the fuck up!
Robin
.577 Tyrannosaur.
Sent from the Kohler Bowl.
Robin
Robin